Toppower Asia home

Energy storage

What is a battery energy storage system (BESS)?

20 ft outdoor high-voltage lithium battery energy storage container rated 1 MW, installed on a concrete pad

A battery energy storage system (BESS) is a complete installation that stores electricity in rechargeable batteries and releases it when needed. Besides the battery cells, it includes a battery management system, a power conversion system that turns DC into grid-compatible AC, thermal management, fire safety equipment and an energy management system that decides when to charge and discharge.

Key takeaways

  • BESS stands for battery energy storage system. The term covers the whole system, not only the battery packs.
  • Every BESS has two separate ratings: power in kW or MW (how fast it can deliver energy) and energy in kWh or MWh (how much it can store).
  • Most new stationary systems use lithium iron phosphate (LFP, LiFePO4) cells because of their thermal stability and long cycle life.
  • The main applications are peak shaving, solar time-shift, backup power, microgrids and grid services such as frequency response.
  • Safety and grid standards (IEC 62619, IEC 62933, UL 9540, UL 9540A, NFPA 855) shape the design as much as the battery chemistry does.

What does BESS mean?

The definition of BESS is simple: a battery energy storage system is any stationary system that charges from an electrical source, holds that energy chemically in batteries and discharges it back to a load or the grid in a controlled way. The word "system" matters. A rack of batteries on its own cannot connect to an AC network, cannot protect itself from overcharge and cannot decide when to operate. The BESS adds the conversion, protection and control layers that make the batteries usable.

In practice, people use "BESS" for anything from a single outdoor cabinet of around 100 kWh at a factory to a utility plant built from dozens of containers totalling hundreds of MWh. The building blocks are the same; only the scale and the grid connection change.

What are the main components of a battery storage system?

A typical BESS system contains the following parts, whether it is supplied as one integrated container or as separate blocks.

ComponentWhat it doesWhat to check in a specification
Battery cellsStore energy electrochemically; LFP is the common chemistry for stationary useChemistry, cell capacity (Ah), cycle-life rating and the test conditions behind it
Modules and racks (clusters)Group cells in series and parallel to reach the DC voltage and capacityDC voltage window, rack fuses and disconnects
Battery management system (BMS)Monitors cell voltage, temperature and current; estimates state of charge; trips protectionArchitecture, balancing method, communication protocols
Power conversion system (PCS)Bidirectional inverter that converts DC to AC on discharge and AC to DC on chargekVA rating, temperature derating, grid-forming or grid-following capability
Thermal managementKeeps cells within their temperature window by air or liquid coolingCooling method, auxiliary power consumption, ambient design range
Fire detection and suppressionDetects off-gas, smoke and heat; suppresses fire; vents explosive gasesGas detection, suppression agent, deflagration venting, test reports
Energy management system (EMS)Decides when and how much to charge or discharge based on tariffs, load and grid signalsControl modes supported, metering interface, remote access
Transformer and switchgearStep the PCS output up to the site or grid voltage and provide isolation and protectionVoltage ratio, vector group, impedance, protection scheme

The BMS is the part that most directly protects the cells. Our guide to the battery management system in a BESS explains its layers and functions in detail.

How does a battery energy storage system work?

The operating cycle is the same for almost every application:

  1. Charging. The PCS takes AC power from the grid, a solar plant or a generator, rectifies it to DC and charges the battery racks. The BMS limits charging current and voltage to keep each cell inside its safe window.
  2. Holding. The system stays idle at a set state of charge. Thermal management and controls continue to draw a small auxiliary load.
  3. Discharging. When the EMS sees a trigger (a demand peak, a price signal, a grid frequency deviation or a power cut), it commands the PCS to invert DC back to AC and deliver it to the load or the grid.
  4. Protection. Throughout, the BMS and PCS monitor for faults. If a cell, rack or the grid goes outside limits, contactors open and the affected section is isolated.

For grid-scale systems, the PCS output at low voltage (often a few hundred volts AC) is stepped up to medium voltage by a transformer. A PCS step-up skid for 10 kV or 15 kV puts the PCS, transformer and switchgear on one transportable base.

What is the difference between kW and kWh in a BESS battery?

Power (kW or MW) is the rate of charge or discharge, set mainly by the PCS and the current rating of the cells. Energy (kWh or MWh) is the amount stored. The ratio between them is the C-rate or, expressed the other way, the duration:

  • A 1 MW / 2 MWh system can discharge at full power for about two hours (0.5C).
  • A 1 MW / 4 MWh system can discharge at full power for about four hours (0.25C).

Both numbers are needed to compare offers. Nameplate energy is also not the same as energy delivered to the meter, because of the usable state-of-charge window, conversion losses and capacity fade over time. Our guide on how to size a BESS container works through these corrections step by step.

Which battery chemistry do stationary BESS use?

Lithium-ion batteries dominate new stationary storage, and within lithium-ion the main stationary choice today is lithium iron phosphate (LFP). The reasons are practical:

  • Thermal stability. LFP cathodes release far less heat and oxygen in abuse conditions than nickel-based chemistries, which reduces the severity of thermal runaway.
  • Cycle life. LFP cells are commonly rated for several thousand full cycles to a defined end-of-life capacity, which suits daily cycling.
  • No cobalt or nickel. This lowers material cost and supply-chain exposure.

The trade-off is lower energy density per kilogram than nickel-manganese-cobalt (NMC) cells. For a building-side cabinet or a container on a concrete pad, that matters far less than it does in a vehicle. Other technologies such as flow batteries, sodium-ion and lead-acid exist, but each has a narrower share of new stationary projects.

What are the main types of battery storage system?

Stationary systems are usually grouped by size and where they connect.

TypeTypical sizeConnection pointCommon format
ResidentialA few kWh to tens of kWhHome low-voltage supplyWall-mounted or floor units
Commercial and industrial (C&I)Roughly 50 kWh to a few MWhBehind the customer meter, low or medium voltageOutdoor cabinets or 10–20 ft containers
Utility-scale (front of the meter)Several MWh to hundreds of MWhMedium or high voltage substation20 ft or 40 ft containers in blocks with step-up transformers
Off-grid and microgridFrom tens of kWh to several MWhIsland network with solar, wind or dieselCabinets or containers with grid-forming PCS

For C&I sites, an outdoor unit from the liquid-cooled storage cabinet range is often the right size. Utility and large solar projects usually build from containers such as the 20 ft outdoor 1 MW high-voltage lithium BESS or other units in the battery energy storage system range.

What is a BESS system used for?

The same hardware can serve very different purposes depending on how the EMS is programmed:

  • Peak shaving. Discharge during the site's highest demand intervals to reduce demand charges. See our guide to peak shaving with battery storage.
  • Solar self-consumption and time-shift. Store midday PV surplus and use it in the evening, or stay within an export limit.
  • Backup power. Supply critical loads during outages, usually with a grid-forming PCS and a transfer scheme.
  • Microgrids and off-grid sites. Form the voltage and frequency reference for an island network and reduce diesel run hours.
  • Grid services. Frequency response, reserves, voltage support and energy arbitrage for utilities and market participants.

Many projects stack two or more of these uses, for example peak shaving on weekdays and backup during outages, provided the state-of-charge strategy leaves enough energy in reserve.

Which standards apply to a battery energy storage system?

The applicable standards depend on the country and on who approves the installation: the authority having jurisdiction, the insurer and the grid operator. Commonly cited ones include:

  • IEC 62619 for safety of secondary lithium cells and batteries in industrial applications, including stationary storage.
  • IEC 62933 series for grid-integrated electrical energy storage systems, including terminology, performance testing and safety (part 5-2 for electrochemical systems).
  • UL 9540 for the safety of energy storage systems and equipment in North America, and UL 9540A as the test method for thermal runaway fire propagation.
  • NFPA 855 for installation of stationary energy storage systems in the US. The NFPA 855 development page shows the current edition and revision status.
  • Grid-connection codes and interconnection standards such as IEEE 1547 in North America, or the national grid code elsewhere.

Ask the supplier for reports that match the exact cell, module, rack and enclosure being offered, not a similar product.

Frequently asked questions

What is BESS in simple terms?

A BESS is a large rechargeable battery with the electronics and controls needed to connect it safely to a building or the grid. It charges when electricity is cheap or plentiful and discharges when it is expensive, scarce or unavailable.

How long can a battery energy storage system supply power?

That depends on the energy-to-power ratio. Most commercial and utility systems are designed for one to four hours at full rated power. At lower power the same energy lasts proportionally longer.

How long does a BESS battery last?

Lifetime is governed by both cycling and calendar ageing. LFP systems are often specified for 10 to 20 years of design life, but the warranted figure depends on cycles per day, temperature and depth of discharge. Ask for a capacity-retention curve under your intended duty cycle.

Is a battery storage system the same as a UPS?

No. A UPS is designed to bridge short interruptions for a specific load, usually for minutes, with very fast transfer. A BESS is designed for daily cycling over hours and for grid interaction. Some BESS can provide backup, but transfer time and load compatibility must be checked separately.

Is a BESS safe?

A well-designed BESS manages risk through cell chemistry, the BMS, thermal management, gas detection, suppression, explosion venting and correct spacing. Safety depends on the complete system and its installation, which is why standards such as UL 9540A and NFPA 855 test and regulate at system and site level.

If you are planning a project, send us your load profile, single-line diagram or draft specification through our contact page. Our engineering team will review it and return a technical proposal with a configured battery, PCS and grid connection.

Toppower Asia Engineering Team

Application and sales engineers at Shanghai Toppower-Asia Co., Ltd. who review specifications and prepare technical proposals for transformers, switchgear, substations and battery storage. Questions about this article: kevin@toppower-asia.com.

More on energy storage

Send your single-line diagram. Get a technical proposal back.

Tell us the rating, voltages and site. Our engineers review it against your network before pricing, and reply with ratings, losses, dimensions, test scope and a quotation.

Rated power, voltages, frequency, standard, site conditions and destination port help us reply with a firm proposal.

Send via WhatsApp

Replies come from kevin@toppower-asia.com. Office hours are Monday to Friday, 9:00–18:00 China Standard Time.

Press Enter to see all matching products. Use ↑ ↓ to move through results.