Toppower Asia home

Transformers

Pole-mounted transformers: sizes, types and installation

Completely self-protected single-phase pole transformer with cover-mounted HV bushing and arrester, side radiators and hanger brackets on a concrete utility pole

A pole mounted transformer is an oil-filled distribution transformer hung on a utility pole that steps an overhead medium-voltage line, typically between about 4 kV and 35 kV, down to low voltage for nearby customers. Most are single-phase units from 10 to 167 kVA supplying 120/240 V or 230 V. Three-phase supply comes from a bank of single-phase units or, in many IEC networks, a three-phase unit.

Key takeaways

  • "Utility pole transformer", "power pole transformer" and "electric pole transformer" all describe the same thing: an overhead-type distribution transformer, covered in North America by IEEE C57.12.20 (500 kVA and smaller, HV 34.5 kV and below).
  • A conventional unit relies on an external fuse cutout and surge arrester; a CSP (completely self-protected) unit has the fuse, arrester and a secondary breaker built in.
  • Single-bushing units connect phase to neutral on multi-earthed wye systems; two-bushing units connect phase to phase.
  • Polarity, mounting arrangement and pole strength must be checked before ordering, especially if units will be banked for three-phase service.

What is a pole mounted transformer and how does it work?

The transformer is a sealed steel tank, usually cylindrical, containing a wound core and coils immersed in mineral oil. The primary (HV) bushing or bushings sit on the cover or the upper tank wall and connect to the overhead line through a fuse cutout. The secondary (LV) bushings, marked X1, X2 and X3 on a 120/240 V unit, are on the side wall, and service drops run from them to customers.

Two hanger brackets welded to the tank bolt to the pole, or to a crossarm or bracket on the pole. The tank has an earthing (grounding) terminal connected to the system neutral and the pole earth electrode. Cooling is natural: heat moves through the oil to the tank wall and, on larger ratings, to external radiators or cooling tubes.

Because the unit is above reach, it does not need the locked, tamper-resistant enclosure of a pad-mounted unit. The trade-offs are exposure to lightning, wildlife and weather, and limits on weight set by the pole. For underground networks, see our pad-mounted transformer guide.

Which sizes are standard for a single phase pole transformer?

Single-phase ratings follow the preferred kVA steps of IEEE C57.12.00. The table shows full-load secondary current at 240 V (I = kVA × 1000 / V).

Rating (kVA)Full-load current at 240 VTypical service
1041.7 AOne or two rural homes
1562.5 ASmall rural load, irrigation pump
25104.2 AA few homes
37.5156.3 ASmall group of homes
50208.3 ASuburban street section, small shop
75312.5 ALarger homes, small commercial
100416.7 ASmall commercial building
167695.8 ACommercial service, one phase of a bank
250 / 333 / 5001,042 / 1,388 / 2,083 ALarge single-phase loads or banks for three-phase industry

For other voltages or three-phase loads, use our transformer calculator.

Ratings above 167 kVA are heavy. Check the pole class, the hanger bracket arrangement and whether the utility prefers a cluster mount, crossarm mount or platform. Our range includes 13.8 kV single-phase pole transformers from 15 to 333 kVA.

Conventional vs CSP transformer: what is the difference?

A conventional pole transformer has no protection of its own. It depends on an external fuse cutout on the primary and a separate surge arrester, both mounted on the pole or crossarm.

A CSP transformer (completely self-protected) integrates three protective elements:

  • a primary protective link, an internal expulsion fuse that disconnects the transformer from the line if it fails internally,
  • a surge arrester mounted on the tank,
  • an internal secondary circuit breaker, which opens on overload or secondary faults and is reset from outside with a hot stick. Many designs add a signal light that warns of sustained overload, and an emergency control that lets the breaker be reset at a higher trip setting temporarily.
FeatureConventionalCSP
Primary protectionExternal fuse cutoutInternal protective link (plus external cutout if the utility requires)
Surge protectionSeparate arrester on pole or crossarmTank-mounted arrester
Secondary overload/fault protectionNone in the transformerInternal secondary breaker
Overload warningNoneSignal light on many designs
Restoring after secondary faultReplace fuse at cutoutReset breaker with hot stick
Pole hardwareMore separate componentsFewer, neater installation
Unit costLowerHigher

CSP units suit long rural feeders where crews travel far, as a tripped secondary breaker can be reset without replacing a fuse. Conventional units are simpler and let the utility standardise fuses and arresters separately. See our completely self-protected 250 kVA pole transformer for an example.

How is a single phase pole transformer connected?

Primary. On a multi-earthed four-wire wye system, the transformer connects between one phase and the neutral. A single-bushing design is normal: the other end of the HV winding is bonded to the tank and the neutral. For a 12.47Y/7.2 kV line the transformer is rated 7,200 V. On a three-wire delta or unearthed system, the transformer connects phase to phase and needs two fully insulated HV bushings.

Secondary. The usual North American secondary is 120/240 V three-wire, with the centre tap (X2) earthed. Many IEC markets use a single 230 V or 240 V secondary, or 220/440 V where required.

Polarity. IEEE C57.12.00 makes single-phase units of 200 kVA and below with HV of 8,660 V and below additive polarity, and larger or higher-voltage units subtractive. Polarity determines how the secondary leads are connected when units are banked, so mixed polarity in a bank must be identified before connection.

Taps. Many specifications call for off-circuit taps, for example two 2.5% steps above and below rated voltage, to correct for voltage drop along long feeders.

How do you get three-phase power from pole transformers?

There are two routes.

  1. A bank of single-phase units. Three identical transformers on a crossarm or cluster mount are connected wye-delta, delta-delta, grounded wye-grounded wye or delta-wye. Two units in open delta, or open wye-open delta, can supply three-phase loads where single-phase demand dominates. Our articles on delta-wye transformer connections and single-phase vs three-phase transformers explain these arrangements.
  2. A three-phase pole-mounted unit. Common in many IEC-based networks for village and rural supplies, typically at 11 kV, 22 kV or 33 kV to 400 V, mounted on a single pole or on a two-pole (H-frame) structure. A three-phase unit is lighter and cheaper than three single-phase units of the same total rating, but a failure takes out all three phases.

For a rural 11 kV/0.4 kV scheme, see our representative configuration for pole-mounted transformers in rural networks.

How is a pole mounted transformer installed?

Installation is work for qualified line crews under the network owner's procedures. A typical sequence:

  1. Confirm the pole class and condition can carry the transformer weight plus wind and ice loading.
  2. Fit the mounting hardware (bolts for the hanger brackets, crossarm or cluster bracket) at the specified height and clearance.
  3. Lift the transformer using its lifting lugs only, with a crane or line truck.
  4. Bolt the hanger brackets, then connect the tank earth and the neutral to the pole earth conductor.
  5. Mount and connect the fuse cutout and arrester (conventional units), with short, direct arrester leads.
  6. Connect the secondary service conductors and check terminal tightness.
  7. Check the tap position, oil level and visible damage, then energise through the cutout and measure secondary voltages and phasing.

What should you specify when buying pole transformers?

  • Standard: IEEE C57.12.20 or IEC 60076, frequency and any utility specification.
  • kVA, primary voltage and connection (phase-to-neutral or phase-to-phase), number of HV bushings.
  • Secondary voltage, terminal arrangement and polarity.
  • Conventional or CSP, plus cutout, arrester and breaker ratings.
  • Losses or efficiency level, such as the DOE 10 CFR 431 minimum efficiencies in the US.
  • Winding material (copper or aluminium), core type, tank coating for coastal or industrial sites, and mounting arrangement.

Browse our full pole-mounted transformer range for single-phase units from 15 kVA to 333 kVA.

Frequently asked questions

What size is a typical utility pole transformer?

Residential pole transformers are usually 25, 37.5 or 50 kVA, serving a handful of homes. Units of 75 to 167 kVA serve larger loads, and the overhead standard IEEE C57.12.20 extends to 500 kVA.

What does CSP mean on a transformer?

CSP stands for completely self-protected. A CSP transformer includes an internal primary protective link, a tank-mounted surge arrester and an internal secondary breaker, so it needs fewer separate protective devices on the pole.

Can a pole mounted transformer supply three-phase power?

Yes. Either three single-phase units are banked together, two units are used in open delta, or a single three-phase pole-mounted transformer is installed, which is common in IEC-based networks.

What voltage comes out of a pole transformer?

In North America it is usually 120/240 V single-phase, three-wire. In IEC markets, single-phase units commonly deliver 230 V or 240 V, and three-phase units deliver 400/230 V.

Is a power pole transformer the same as a distribution transformer?

Yes. A power pole transformer is an overhead-type distribution transformer. "Power transformer" in the strict sense usually refers to larger substation units.

Ask for a pole transformer proposal

Send us your line voltage, earthing system, kVA ratings, secondary voltage and any utility specification. Our engineers will propose conventional or CSP designs, connections and accessories in a technical proposal. Contact our team.

Toppower Asia Engineering Team

Application and sales engineers at Shanghai Toppower-Asia Co., Ltd. who review specifications and prepare technical proposals for transformers, switchgear, substations and battery storage. Questions about this article: kevin@toppower-asia.com.

More on transformers

Send your single-line diagram. Get a technical proposal back.

Tell us the rating, voltages and site. Our engineers review it against your network before pricing, and reply with ratings, losses, dimensions, test scope and a quotation.

Rated power, voltages, frequency, standard, site conditions and destination port help us reply with a firm proposal.

Send via WhatsApp

Replies come from kevin@toppower-asia.com. Office hours are Monday to Friday, 9:00–18:00 China Standard Time.

Press Enter to see all matching products. Use ↑ ↓ to move through results.