Toppower Asia home

Application example · Egypt · 50 Hz

66 kV/11 kV Oil-Immersed Grid Transformer

A 66 kV unit is a sub-transmission grid transformer, not a distribution transformer, and four consequences follow from that.

Country
Egypt
System
66 kV/11 kV
Frequency
50 Hz
Package
9 equipment items
This is a representative application example describing a typical configuration for a 66 kV/11 kV oil-immersed grid transformer at a utility substation in a desert environment, and the scope Toppower Asia can supply against a comparable enquiry. The images are illustrative renderings, not a record of any specific completed installation, and show no real customer, site, utility, network owner, contract, energisation date or certification. All ratings, quantities and arrangements are indicative and would be confirmed against an actual enquiry.

Project snapshot

CountryEgypt
ApplicationUtility transmission/distribution substation in a desert climate
System66 kV/11 kV oil-immersed grid transformer with radiator cooling and on-load tap changer
Voltage66 kV primary / 11 kV secondary
Frequency50 Hz
Design standardsIEC 60076 series (-1 general, -2 temperature rise, -3 insulation levels and dielectric tests, -5 short-circuit withstand, -7 loading guide, -10 sound levels); IEC 60214-1 and IEC 60076-21 (tap changers); IEC 60137 (bushings); IEC 60099-4 (surge arresters); IEC 61869 (instrument transformers); IEC 60815 (insulator selection for polluted conditions); IEC 61936-1 and IEC 62271-202 practice for bay and containment; the purchasing network owner's specification prevails where stricter

Site and grid challenges

A 66 kV unit is a sub-transmission grid transformer, not a distribution transformer, and four consequences follow from that.

It must hold the busbar voltage. An 11 kV bus fed from the 66 kV system has to stay within limits while both the upstream voltage and the downstream load change through the day. That requires an on-load tap changer under the control of an automatic voltage regulator; off-circuit tap links cannot do it. Tapping range, step size and regulation band are taken from a voltage study of the network at the connection point. The tap changer then becomes the transformer's only moving mechanism and its main maintenance item.

It needs unit protection. At this rating and network position, the transformer is protected by differential relaying with ratio and vector-group compensation, restricted earth-fault protection on the windings, and Buchholz gas and oil-surge relays that detect developing internal faults before they become electrical failures. Buchholz protection is not a duplicate of the differential scheme — it detects slow gas generation that a differential relay will never see.

The oil is an environmental matter as well as an insulating medium. A bunded, drained pit able to hold the entire oil volume plus firefighting water, with suitable separation from neighbouring plant, is part of both the electrical design and the civil works.

Desert ambient is the governing design case. The cooling-air temperatures in IEC are reference values; where the site exceeds them, the transformer must be specified with a reduced temperature rise or additional cooling surface. Sand and dust clog radiator fins, block filters and settle on bushings, increasing both the creepage class required and the cooling margin needed.

Typical equipment package

What a project of this type usually includes, and the engineering points that decide each item.

EquipmentRoleEngineering notes
Tank and active partThree-phase oil-immersed core-type transformer, 66 kV/11 kVInsulation levels to IEC 60076-3 for the 66 kV system; short-circuit withstand shown to IEC 60076-5 against the actual network fault level; core flux density designed for 50 Hz, so a 60 Hz design is not a direct substitute
CoolingRemovable radiator banks, ONAN or ONAF with staged fansRating stated at the real site design ambient, not the reference ambient; fin pitch and filtration chosen for airborne sand; fan stages driven by oil and winding temperature
On-load tap changerDiverter/selector with motor drive, automatic voltage regulator and remote indicationRange and step size from the voltage regulation study; separate OLTC oil compartment with its own conservator section and protective relay; operations counter and mechanism heater included
Conservator and oil preservationConservator with rubber diaphragm or air cell, plus dehydrating breatherSealed system keeps moisture out of the oil — important where wide daily temperature swings cause heavy breathing; breather condition is a routine inspection item
Bushings66 kV HV, 11 kV MV and neutral bushingsCreepage per IEC 60815 for the site pollution class, as desert dust plus dawn condensation becomes conductive; type, angle and clearances coordinated with the bay layout
Surge arrestersMetal-oxide arresters on HV and MV sidesRated and continuous operating voltage derived from system earthing; short, direct earth leads, because lead inductance can negate a correctly rated arrester
Protection and monitoringDifferential and REF protection, Buchholz and oil-surge relays, pressure relief device, oil and winding temperature indicators, oil level gaugeCT ratios and vector compensation set in the relay; separate Buchholz alarm and trip circuits; thermal-image winding temperature with fan and alarm contacts; online dissolved gas analysis optional
Oil containmentBunded, drained pit under the transformer with oil separator and fire-water provisionCapacity for full oil volume plus water; separation distances and any firewall per the bay design practice
Auxiliaries and interfacesMarshalling kiosk, control and alarm wiring, anti-condensation heating, communication gatewayKiosk IP rating and gaskets specified against sand ingress; links to the substation control system via IEC 61850, IEC 60870-5-104 or Modbus

Stage by stage

The sequence at a glance

The overview presents four typical stages: multi-axle heavy haulage, placement with radiator assembly, bushing and auxiliary connection, and the finished transformer bay. The order is dictated by the tank. Radiators, conservator and frequently the bushings are shipped separately and fitted after placement. Oil processing follows mechanical assembly, and the tank is never exposed to desert air for longer than its permitted limit. Electrical testing is carried out after oil filling and the standing period that allows entrained gas to disperse, and the bay is closed and containment completed only after the unit has been proven.

  1. Large oil-immersed power transformer on a multi-axle trailer on a desert road
    Illustrative multi-axle transport of an oil-immersed grid transformer of the type used in desert substations
    Stage 1 of 4

    Delivery

    A 66 kV transformer is an indivisible load moved on a multi-axle trailer, with the route engineered before dispatch. Axle loads, bridge and culvert ratings, gradients, camber, overhead clearances and turning radii are all surveyed, and desert road sections are tested for bearing capacity wherever shoulders appear soft. The tank is transported braced, typically filled with dry air or nitrogen at a positive pressure that is recorded along the route, and carries multi-axis impact recorders. On arrival, recorder data is downloaded and compared with the agreed limits before off-loading; an exceedance calls for inspection of the active part rather than proceeding regardless. Gas pressure, dew point and the condition of valves and blanking plates are checked and documented at handover.

  2. Crane setting an oil-immersed transformer tank on its plinth while radiator banks are assembled beside it
    Representative placement and radiator assembly of a grid transformer of this class
    Stage 2 of 4

    Placement and assembly

    The unit is positioned using its designated jacking pads and lifting lugs, with the lift plan accounting for a high centre of gravity that rises further once the tank is filled. Plinth and rails are checked for level, because a tilted tank distorts oil-level indication and can leave a radiator bank partially empty. Wheels or rails are locked and the transformer anchored to the bay's seismic and wind detail. Radiators, conservator and pipework are fitted with new gaskets, and every valve position is checked and recorded — a closed radiator valve is a surprisingly common cause of overheating in service. Oil is filled under vacuum via a treatment plant, with moisture, breakdown voltage and dissolved gas sampled before and after, and the unit is then allowed to stand so trapped air can escape before voltage is applied.

  3. Close-up of high-voltage bushings, surge arresters, conservator piping and marshalling kiosk on an oil-immersed transformer
    High-voltage bushings, surge arresters and auxiliary connections of the type fitted to grid transformers
    Stage 3 of 4

    Connection

    Bushing installation demands precision. Each bushing is examined for transit damage and oil level, and its capacitance and tan-delta are compared with the factory certificate; it is then fitted with correct gasket compression and bolt sequence, and the draw-lead connection made without twisting the inner conductor. Live-to-earth and phase-to-phase clearances are measured on the installed arrangement. Surge arresters are mounted with the shortest practical earth lead taken directly to the bay earth grid. Auxiliary work includes setting the Buchholz relay angle and pipe slope — the relay does not work on a level pipe — the pressure relief device, oil and winding temperature indicators with capillaries shaded from direct sun, the tap-changer drive with its limits and interlocks, and the marshalling kiosk with heater, seals and cable glands.

  4. Finished transformer bay with an oil-immersed grid transformer above a bunded containment area, fenced and connected
    Illustrative completed configuration of a 66 kV/11 kV grid transformer bay with radiator cooling and oil containment
    Stage 4 of 4

    Completed configuration

    The completed configuration shows the transformer in a fenced bay above its containment pit, with radiators, conservator, arresters and marshalling kiosk installed. Before energisation every link is checked: insulation resistance and polarisation index, winding resistance and turns ratio on every tap, vector group, magnetising current, and capacitance and tan-delta of windings and bushings, along with a final oil sample for moisture, breakdown voltage and dissolved gas that becomes the reference for all later samples. Protection is tested end-to-end by injection, including differential stability, with Buchholz alarm and trip paths proven separately. The tap changer is run across its full range under observation and the counter reading noted. Energisation is staged: the transformer is charged off-load, inspected and left to soak before load is applied.

What Toppower can configure

For a comparable utility enquiry, Toppower Asia can configure a grid transformer around the required rating, impedance and tolerance, vector group and neutral arrangement, with tapping range, step size and regulation band derived from the voltage study. Cooling can be ONAN, ONAF or dual-rated ONAN/ONAF, with defined fan stages and the rating declared at a stated site ambient. On-load or off-circuit tap changing can be supplied, together with an automatic voltage regulator, parallel-operation scheme and remote indication. Bushing creepage can be matched to the site pollution class and surge arresters coordinated with system earthing. Protection and monitoring can range from conventional differential, REF, Buchholz and temperature devices to online dissolved gas and bushing monitoring, communicating via IEC 61850, IEC 60870-5-104 or Modbus. Loss capitalisation, sound-level limits, containment arrangement, paint system and corrosivity class can all be specified as required.

Information needed for a quotation

Tick what you can already provide; checked items are added to your enquiry.

Your checklist0 of 12

Rated power, voltages, frequency, standard, site conditions and destination port help us reply with a firm proposal.

Send via WhatsApp

Replies come from kevin@toppower-asia.com. Office hours are Monday to Friday, 9:00–18:00 China Standard Time.

Press Enter to see all matching products. Use ↑ ↓ to move through results.