# kVA vs kW: what the difference means for transformer sizing

Published 2026-10-13 by Toppower Asia Engineering Team · https://www.toppower-asia.com/blog/kva-vs-kw-explained/

The difference in kVA vs kW is the difference between apparent power and real power. kW (kilowatts) is the power that does useful work, such as turning a shaft or heating a room. kVA (kilovolt-amperes) is voltage multiplied by current, which is what heats cables and transformer windings. The two are linked by power factor: kW = kVA × PF. Transformers are rated in kVA because their limit is current, not useful output.

## Key takeaways

- kVA is apparent power (volts × amps). kW is real power. kvar is the reactive power that makes up the difference.
- kW = kVA × power factor, and kVA = kW / power factor. At 0.8 power factor, 1000 kVA delivers only 800 kW.
- Three-phase current: I = kVA × 1000 / (√3 × V). Single-phase: I = kVA × 1000 / V.
- Size transformers, generators, cables and switchgear on kVA (or current), not on kW alone.
- Our [transformer calculator](https://www.toppower-asia.com/tools/transformer-calculator/) converts kVA, kW and amps and suggests the next standard rating.

## What is kVA and what does kVA mean?

kVA stands for kilovolt-ampere, one thousand volt-amperes. It is the product of the RMS voltage and RMS current in a circuit, with no allowance for the phase angle between them. That product is called apparent power.

The kVA meaning matters because current is what a conductor feels. A winding heats up according to I²R, regardless of whether the current is doing useful work or simply flowing back and forth to magnetise a motor. A transformer manufacturer therefore cannot know how many kW you will draw, because that depends on your load's power factor. What the manufacturer can guarantee is that the transformer will carry a given current at a given voltage without exceeding its temperature rise limits. That is a kVA rating.

The same logic applies to generators, UPS systems and inverters. Their windings and semiconductors are current-limited, so they carry a kVA rating, often accompanied by a kW rating at a stated power factor.

## What is the difference between kVA and kW?

kW is real (active) power: the energy per second actually converted into mechanical work, heat or light. Your energy meter records kWh, the integral of kW over time.

kVA is apparent power. Between the two sits reactive power, measured in kvar, which flows into the magnetic fields of motors and transformers and the electric fields of capacitors and cables, then back again each cycle. It does no net work but it still needs current.

The three quantities form the power triangle:

- **kVA² = kW² + kvar²**
- **Power factor (PF) = kW / kVA = cos φ** for sinusoidal waveforms, where φ is the angle between voltage and current.

| Quantity | Symbol | Unit | What it represents | Where you see it |
|---|---|---|---|---|
| Real power | P | kW | Useful work: torque, heat, light | Motor shaft output, energy bills (kWh) |
| Reactive power | Q | kvar | Energy exchanged with magnetic and electric fields | Capacitor banks, utility kvarh charges |
| Apparent power | S | kVA | Voltage × current; what heats conductors | Transformer, generator and UPS ratings |
| Power factor | PF or cos φ | (ratio 0 to 1) | Share of apparent power that does work | Motor nameplates, tariff penalties |

## What is power factor and why does it matter?

Power factor is the ratio of kW to kVA. A purely resistive heater has a power factor close to 1.0: every amp does useful work. An induction motor on light load can drop to 0.3 or 0.4, because most of its current magnetises the iron. At full load, typical induction motors run at about 0.8 to 0.9.

Low power factor costs money in three places:

1. **Equipment size.** More kVA for the same kW means a larger transformer, larger cables and larger breakers.
2. **Losses.** Load losses rise with the square of current. Carrying extra reactive current through the network wastes energy.
3. **Tariffs.** Many utilities charge for reactive energy or demand, or penalise a monthly power factor below a threshold.

Power factor correction capacitors on the LV bus supply the reactive power locally, so the transformer only carries the reduced kVA. Where drives and rectifiers distort the current, the true power factor also includes a distortion component, and plain capacitors can resonate with the transformer. In that case detuned or active filters are used instead.

## How do you convert kVA to kW, and kW to kVA?

The formulas are simple:

- **kW = kVA × PF**
- **kVA = kW / PF**
- **kvar = √(kVA² − kW²)**

**Example 1: what can a 1000 kVA transformer supply?**
At PF 0.8: 1000 × 0.8 = **800 kW**. At PF 0.95: 1000 × 0.95 = **950 kW**. The transformer is the same; the load's power factor decides how many kW it can deliver at full current.

**Example 2: sizing for a known kW load.**
A pumping station has 250 kW of maximum demand at PF 0.85.
kVA = 250 / 0.85 = **294 kVA**. The next standard IEC rating above that is 315 kVA, but at 93 percent loading there is little headroom, so most designers would consider 400 kVA. If PF correction raises the power factor to 0.95, demand falls to 263 kVA, and 315 kVA runs at about 84 percent.

**Example 3: reactive power.**
For the pumping station at PF 0.85: kvar = √(294² − 250²) ≈ **155 kvar**. A capacitor bank sized to bring PF to 0.95 would need to supply roughly 155 − 82 = 73 kvar, because at 0.95 the remaining reactive demand is √(263² − 250²) ≈ 82 kvar.

Always add loads as kW and kvar separately, then combine. Adding kVA values that have different power factors overstates the total, as explained in [how to size a distribution transformer](https://www.toppower-asia.com/blog/how-to-size-a-distribution-transformer/).

## What is the kVA to amps formula?

Current is what you need for cable, busbar and breaker selection, so the kVA to amps formula is the most-used equation in distribution design.

**Three-phase:**

- **kVA = √3 × V × I / 1000**
- **I = kVA × 1000 / (√3 × V)**

where V is the line-to-line voltage in volts and I is the line current in amps. √3 ≈ 1.732.

**Single-phase:**

- **kVA = V × I / 1000**
- **I = kVA × 1000 / V**

**Example 4: secondary current of a 1000 kVA, 11 kV/400 V transformer.**
I = 1,000,000 / (1.732 × 400) ≈ **1443 A** on the LV side. On the 11 kV side: 1,000,000 / (1.732 × 11,000) ≈ **52.5 A**. The main LV breaker would typically be a 1600 A frame.

**Example 5: a 1500 kVA pad-mounted unit at 480 V.**
I = 1,500,000 / (1.732 × 480) ≈ **1804 A**.

**Example 6: a 50 kVA single-phase pole transformer at 240 V.**
I = 50,000 / 240 ≈ **208 A** on the 120/240 V secondary.

**Example 7: working backwards from current.**
A 400 V switchboard measures 600 A per phase at PF 0.88.
kVA = 1.732 × 400 × 600 / 1000 ≈ **416 kVA**, and kW = 416 × 0.88 ≈ **366 kW**.

The table gives full-load currents for common three-phase ratings. Use the [transformer calculator](https://www.toppower-asia.com/tools/transformer-calculator/) for other voltages.

| Rating (kVA) | kW at PF 0.8 | Current at 400 V (A) | Current at 415 V (A) | Current at 480 V (A) |
|---|---|---|---|---|
| 250 | 200 | 361 | 348 | 301 |
| 500 | 400 | 722 | 696 | 601 |
| 630 | 504 | 909 | 876 | 758 |
| 1000 | 800 | 1443 | 1391 | 1203 |
| 1600 | 1280 | 2309 | 2226 | 1925 |
| 2500 | 2000 | 3608 | 3478 | 3007 |

## Why are transformers rated in kVA and not kW?

A transformer's limits are thermal and dielectric. Load losses depend on current, and core losses depend on voltage and frequency. Neither depends on the phase angle between voltage and current. A transformer supplying 1000 A at zero power factor heats up just as much as one supplying 1000 A at unity power factor, even though the first delivers no real power.

So IEC 60076-1 defines rated power in kVA (or MVA), and the nameplate states kVA. Generators are a slightly different case: they are rated in kVA but usually at 0.8 power factor, because the prime mover (engine or turbine) limits kW while the alternator limits kVA. A 1250 kVA genset at 0.8 PF is a 1000 kW engine. If your load runs at unity power factor, you still only get 1000 kW, because the engine is the bottleneck.

For the same reason, battery storage PCS and solar inverters often state both kW and kVA. An inverter rated 1000 kW / 1100 kVA can deliver full active power while also supplying some reactive power for grid support. The step-up transformer behind it must be sized for the kVA, not the kW. See [how to size a BESS container](https://www.toppower-asia.com/blog/how-to-size-a-bess-container/) for that calculation.

## How does kVA vs kW affect equipment selection on a real project?

A practical sequence for a new LV supply:

1. List loads in kW with their power factors (or kVA where only that is known).
2. Apply demand and diversity factors per group.
3. Sum kW and kvar separately and calculate total kVA.
4. Decide whether PF correction is economic; if so, recalculate kVA at the corrected power factor.
5. Add growth margin, then choose the next standard kVA rating.
6. Calculate full-load current at the secondary voltage to select the LV main breaker, busbar and cables.
7. Check the generator, if any, against both its kVA and kW ratings.

For a 400 V site with about 800 kVA of design demand, that leads to a 1000 kVA unit such as an [oil-filled distribution transformer in the 100 to 1600 kVA range](https://www.toppower-asia.com/products/oil-immersed-transformer/oil-filled-distribution-transformer-100-1600kva-for-11/), feeding a 1600 A [withdrawable LV switchboard](https://www.toppower-asia.com/products/switchgear/multi-voltage-400v-480v-withdrawable-lv-switchboard/). For a single-phase rural supply, the same arithmetic leads to a [pole-mounted transformer](https://www.toppower-asia.com/blog/pole-mounted-transformer-guide/) in the 25 to 167 kVA range.

## Frequently asked questions

### Is 1 kVA equal to 1 kW?

Only at unity power factor. In general 1 kVA = 1 kW × (1 / PF), so 1 kVA delivers 0.8 kW at PF 0.8. Resistive loads such as heaters come close to unity; motor loads do not.

### How do I convert kVA to kW?

Multiply kVA by the power factor: kW = kVA × PF. If the power factor is unknown, 0.8 is a common conservative assumption for mixed industrial loads, but use measured or nameplate values where you have them.

### What is the kVA to amps formula for three-phase?

I = kVA × 1000 / (√3 × V), with V the line-to-line voltage. For example, 630 kVA at 400 V gives about 909 A. For single-phase, divide kVA × 1000 by the voltage only.

### Why do generators show both kVA and kW?

The alternator is limited by current (kVA) and the engine by real power (kW). Generators are usually rated at 0.8 PF, so the kW rating is 80 percent of the kVA rating. Check both against your load.

### Does improving power factor reduce the transformer size I need?

Yes, for the same kW demand. Raising PF from 0.8 to 0.95 cuts kVA by about 16 percent. Make sure the capacitor bank is switched in steps and, where there are harmonics, detuned, so it does not overcorrect or resonate.

## Get a sizing check and proposal

If you have a load list in kW and need the right kVA rating, voltage and protection, send your single-line diagram and load schedule to our engineers. We will return a technical proposal with the transformer rating, full-load currents and matching switchgear. [Contact Toppower Asia](https://www.toppower-asia.com/contact/).
